Update Samsung Galaxy S Advance Official Jelly Bean Android 4.1.2 (XXLQE)

Samsung just released the official Android 4.1.2 (XXLQE) for the international version of the Galaxy S Advance (GT-i9070). It is only available in a few countries but here I bring you a tutorial so you wont have to wait and you can enjoy all the new Jelly Bean now!


 Galaxy S Advance Jelly Bean

This update fixes several bugs and brings performance improvements and user interface improved. If you were already running Android 4.1.2 and had some lag or other problems, you should try this new build XXLQE.

This is a free terminal firmware, without logos or operators bloatware and can be configured in Spanish.

firmware data

  • PDA: I9070XXLQE
  • CSC: I9070DBTLQ1, I9070XXLQE, I9070OXELPA
  • Baseband / Modem: I9070XXLQE
  • Android version: 4.1.2 Jelly Bean
  • Date: April 9, 2013
  • Region: Europe
  • Country: Germany, Poland, Ukraine

Prerequisites:

  • All data, such as contacts, SMS, photos, music and videos will be deleted if these are stored in the phone. Please do not do a backup of the data with KIES as it creates the backup in the format (. SBU) sometimes have problems in restoring or recognize the phone. Therefore, we strongly recommend that the backup contacts and SMS is done by following the steps below:
    • SMS – Use “SMS Backup and Restore app
    • Contacts – Sync with the Gmail application
    • Songs, Videos, Files – Copy to SD card
    • Note the APN and MMS settings in Applications> Settings> Wireless & networks> , Mobile Networks> APN
  • Make sure all security solutions such as firewalls, antivirus, and also the KIES application close completely until firmware update finishes.
  • Please note that you will have to charge your phone at least 60% battery to ensure that does not interrupt the update.
  • Never interrupt the firmware update process manually, in case, if it is interrupted by power failure then no need to worry because all you have to do is to just follow the instructions again from the beginning.
  • is very important that you make sure you have ADMIN privileges before proceeding to update the phone. You must also enable the USB port which means that you must have read / write so that the firmware can be applied successfully. To do this go to Settings -> Applications -> Development -> USB Debugging . Note that the phone must be disconnected from the computer when you do this step.
  • This process should be carried out ONLY on Samsung Galaxy S Advance (GT-i9070) and NOT on other versions.

 Galaxy S Advance Android Jelly Bean 412

Tutorial Upgrade Samsung Galaxy S4 Official Jelly Bean Android 4.2.2

It is clear that

from AndroidZone we are not responsible for any damage that may happen to your device during this process. Acts under YOUR own risk.

1 – The first thing to do is download the files you will use to update the firmware XXLQE:

2 – After you extract them to get files. tar or. tar.md5, connect your Galaxy S Advance to the PC using the original USB cable and place the firmware file on your phone.

3 – Then unplug the device and turn it off in order to start Mode Download (Volume down + center button + power button) . If you’ve done well, you should see a green robot, which will tell you entered into Download Mode.

4 – Once your Galaxy S Advance mode is Download, connect the device to the computer using the original USB cable. There you will see that the section ID: COM is illuminated.

5 – Then select the files you’ve extracted the folder 13px;line-height: 19px”> 13px;line-height: and F.Reset Time 13px;line-height: are selected and that Re-Partition 13px;line-height: is NOT selected (only select it if you use a. Pit).

Finally click Start to start the installation process.

6 – Once the firmware has been successfully updated, you must disconnect the USB cable and turn off the device to Recovery Mode. For this you press the Volume Up + Home button , and while holding both simultaneously press the power button .

7 – Recovery mode , select Wipe data / factory reset and Wipe Cache partition and then restart the phone by selecting Reboot system now with the help of the volume keys to scroll.

8 – Ready! ‘ve Already updated your Galaxy S to Android 4.1.2 Advanvce Jelly Bean with official firmware XXLQE

To change the default language must go to Settings -> Language and input . It is also advisable to reconfigure the APN settings to avoid connection problems.

What do you think this new firmware? Tell me your experiences in the comments!


Update Samsung Galaxy S Advance Official Jelly Bean Android 4.1.2 (XXLQE)
Source: english  
May 3, 2013


Next Random post